EZ-DRY SLURRY DRYERS

electric-evaporator-banner-mobile

Electric or Gas Fired Slurry Dryers

Available Models

Typical Layout Diagram

Features & Benefits

Options & Accessories

Specifications

Pricing

ACHIEVE ZLD WITH EZ-DRY

Ready to completely eliminate liquid waste hauling or liquid discharge from your facility?  The easy to install, compact, gas fired or all-electric EZ-Dry slurry dryer from EZ Industrial Equipment reduces your waste stream or slurry to a dry solid.  Eliminate liquid waste hauling with EZ-Dry!

ez-dry1

ELECTRIC MODEL
EZD-E13
(13 GPH)

  • Electrically heated - 34 kW/hr
  • 13 gallons per hour*
  • Standard materials of construction for wetted components are 316L Stainless Steel or 2205 duplex.  Upgraded alloys available.  Contact for pricing.
  • 112 gallon capacity tank
  • Footprint:  64" x 44" x 48" (L x W x H)
  • Available in 240V-3PH or 480V-3PH
  • 1 Year Limited Warranty
VIEW PRICING CONTACT SALES
ez-dry1

GAS MODEL
EZD-G13
(13 GPH)

  • Gas fired - 205,000 BTU/hr
  • 13 gallons per hour*
  • Standard materials of construction for wetted components are 316L Stainless Steel or 2205 duplex.  Upgraded alloys available.  Contact for pricing.
  • 112 gallon capacity tank
  • Footprint:  64" x 44" x 48" (L x W x H)
  • 120V-1PH
  • 1 Year Limited Warranty
VIEW PRICING CONTACT SALES

*Evaporation rate is based on tap water after reaching a boil. Evaporation rate may vary depending on altitude, ambient temperature and humidity, solids buildup on evaporator surfaces, boiling point elevation, exhaust stack configuration, off-spec power supply or gas pressure, characteristics of wastewater, etc.

ZLD Wastewater Treatment Solutions - Typical Layout:

  • Primary Treatment: Evaporator system for bulk dewatering
  • Secondary Treatment: Dryer system for final dewatering, solids to landfill
ZLD flow diagram

KEY FEATURES & BENEFITS

AStainless Steel Exterior Skins (click for info) BSolids Removal Tray (click for info) CCorrosion Resistant Materials of Construction (click for info) DReliable Burner System (click for info) EReliable Instrumentation (click for info) FEZ-LOGIC™ Controls (click for info) GAnchor Holes in Foot Pads (click for info) ez-dry7
A

Stainless Steel Exterior Skins

Stainless steel exterior skins to enhance longevity of the equipment.
B

Solids Removal Tray

The rugged design of EZ-Dry's solids removal tray allows for easy removal of residual solids.

C

Corrosion Resistant Materials of Construction

The wetted surfaces are fabricated utilizing corrosion resistant materials of construction.  EZ-Dry is available in the following MOC:

  • 316SS
  • 2205 duplex
  • 6% Moly alloys
  • 2507 super duplex
  • Hastelloy C276, C22
  • Contact EZ for additional options
D

Reliable Burner System

The reliable EZ-Dry burners (gas fired systems only) can utilize natural gas or propane.  EZ-Dry's flue gas exhaust system, comes with test ports used to confirm combustion efficiency, maximizing safe and efficient long term operation.
E

Reliable Instrumentation

EZ-Dry is equipped with reliable level switches and thermocouples promoting safe operation.
F

EZ-LOGIC™ Controls

The core principle of EZ-Dry is simplicity of operation.  No PLC!  The simple yet sophisticated control system is equipped with instrumentation-based safeties and redundancies.  
G

Anchor Holes in Foot Pads

1/2" holes in foot pads allow anchoring to facilitate bolting unit to floor.

OPTIONS & ACCESSORIES

centrifugal feed pump

Self-Priming Feed Pump

The 50 gpm self-priming centrifugal pump is used to fill the evaporator from a nearby feed tank or pit. Energized manually by a toggle switch on the control panel. Heavy duty cast iron, 50 gpm, with 1/2 HP motor.

Pre-Plumbed Fill Pump

Pre-Plumbed Fill Pump

The EZ-Dry fill assembly includes the components and controls to facilitate batch filling of the evaporator.  The fill assembly includes valve, centrifugal feed pump, feed line piping, and controls.

suction wand assembly

Suction Wand/Hose Assembly

Ergonomically designed rigid CPVC wand with 20' x 1" flexible vacuum hose used to pump water from a feed tote or tank into the dryer.  Discharge end of hose connects to the inlet of a 1" centrifugal pump (pump sold separately) using an included quick disconnect cam and groove fitting.  

DF3000 defoamer

EZ-DF3000 Defoamer - 5 Gal. Pail

5 gallon pail of defoamer. Add to feed tank or dryer tank as needed to control foaming.